digitron semiconductors 144 market street kenilworth nj 07033 usa phone +1.908.245-7200 fax +1.908.245-0555 sales@digitroncorp.com www.digitroncorp.com rev. 20130115 mcr106 series silicon controlled rectifiers available non-rohs (standard) or rohs compliant (add pbf suffix). available as ?hr? (high reliability) screened per mil-prf- 19500, jantx level. add ?hr? suffix to base part number. maximum ratings rating symbol value unit peak repetitive off-state voltage (1) (t j = -40 to +110c, sine wave, 50 to 60hz, gate open) MCR106-1 mcr106-2 mcr106-3 mcr106-4 mcr106-5 mcr106-6 mcr106-7 mcr106-8 v drm v rrm 30 60 100 200 300 400 500 600 v on-state rms current (180 conduction angles, t c = 93c) i t(rms) 4.0 a average on-state current (180 conduction angles, t c = 93c) i t(av) 2.55 a peak non-repetitive surge current (half-cycle, sine wave, 60hz, t j = 110c) i tsm 25 a circuit fusing consideration (t = 8.3ms) i 2 t 2.6 a 2 s forward peak gate power (pulse width 1.0s, t c = 93c) p gm 0.5 w forward average gate power (t = 8.3ms, t c = 93c) p g(av) 0.1 w forward peak gate current (pulse width 1.0s, t c = 93c) i gm 0.2 a peak reverse gate voltage (pulse width 1.0s, t c = 93c) v rgm 6.0 v operating junction temperature range t j -40 to +110 c storage temperature range t stg -40 to +150 c mounting torque (2) - 6.0 in. lb. note 1: v drm and v rrm for all types can be applied on a continuous basis. ratings apply for zero or negative gate voltage; positive gate voltage sh all not be applied concurrent with negative potential on the anode. blocking voltages shall not be tested with a constant current source such that the voltag e ratings of the devices are exceeded. note 2: torque rating applies with use of compression washer. mounting torque in excess of 6 in. lb. does not appreciably lowe r case-to-sink thermal resistance. anode lead and heatsink contact pad are common. for soldering purposes, soldering temperatures should not exceed +200c. for optimum results, an activated flux is recommended. thermal characteristics characteristic symbol maximum unit thermal resistance, junction to case r ? jc 3.0 c/w thermal resistance, junction to ambient r ? ja 75 c/w lead solder temperature (lead length 1/8? from case, 10s max) t l 260 c electrical characteristics (t c = 25c, unless otherwise noted) characteristic symbol min typ max unit off characteristics peak forward or reverse blocking current (v ak = rated v drm or v rrm , r gk = 1000 ? ) t c = 25c t c = 110c i drm, i rrm - - - - 10 200 a on characteristics peak forward on-state voltage (3) (i tm = 4.0a peak) v tm - - 2.0 v
digitron semiconductors 144 market street kenilworth nj 07033 usa phone +1.908.245-7200 mcr106 series silicon controlled rectifiers gate trigger current (continuous dc) (4) (v ak = 7v, r l = 100? ) (t c = -40c) gate trigger voltage (continuous dc) (4) (v ak = 7v, r l = 100? ) gate non-trigger voltage (4) (v ak = 12v, r l = 100 ? , t j = 110c) holding current ( v ak = 7v, initiating current = 200ma, gate open) dynamic characteristics critical rate of rise of off-state voltage (t c = 110c) dv/dt - 10 - v/s note 3: pulse width 1.0ms, duty cycle 1%. note 4: r gk current is not included in measurement. mechanical characteristics case to-126 marking alpha-numeric pin out see below fax +1.908.245-0555 sales@digitroncorp.com www.digitroncorp.com rev. 20130115
digitron semiconductors 144 market street kenilworth nj 07033 usa phone +1.908.245-7200 mcr106 series silicon controlled rectifiers fax +1.908.245-0555 sales@digitroncorp.com www.digitroncorp.com rev. 20130115
|
